Product ID:LAM X500 WHITE 17875, 7311T101
MSDS Date:07/02/1991
FSC:8010
NIIN:00N021192
MSDS Number: BLMGR

DEXTER CROWN METRO AEROSPACE COATINGS

31500 HAYMAN
HAYWARD, CA 94544
US

Emergency Phone: 415-471-7171; 415-791-1961

Info Phone: 415-471-7171; 415-791-1961

Preparer: K BUNTON

Cage: 0S4B8

CROWN METRO AEROSPACE COATINGS INC SUB OF DEXTER CORP THE

5695 GREENVILLE, SC 29606 US

Telephone: 803-277-1870

Cage: 0S4B8

N-BUTYL ACETATE (SARA III)

CAS: 123-86-4

RTECS: AF7350000

Fraction By Weight: <10%

OSHA PEL 150 PPM/200 STEL

ACGIH TLV: 150 PPM/200STEL;9192

EPA Report Quantity: 5000 LBS

DOT Report Quantity: 5000 LBS

METHYL ETHYL KETONE (2-BUTANONE) (MEK) (SARA III)

CAS: 78-93-3

RTECS: EL6475000

Fraction By Weight: <10%

OSHA PEL 200 PPM/300 STEL

ACGIH TLV: 200 PPM/300STEL 9192

EPA Report Quantity: 5000 LBS

DOT Report Quantity: 5000 LBS

TOLUENE (SARA III)

CAS: 108-88-3

RTECS: XS5250000

Fraction By Weight: <10%

OSHA PEL 200 PPM/150 STEL

ACGIH TLV: 50 PPM; 9293

EPA Report Quantity: 1000 LBS

DOT Report Quantity: 1000 LBS

ACETIC ACID, 2-METHOXY-1-METHYLETHYL ESTER; (1-METHOXY

CAS: 108-65-6

RTECS: AI8925000

Fraction By Weight: 10-20%

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:(ACUTE) OVEREXPOSURE BY INHALATION MAY
CAUSE IRRITATION OF THE RESPIRATORY TRACT, HEADACHE, DIZZINESS, OR
DROWSINESS. SKIN OR EYE: IRRITANT TO THE EYES AND SKIN. (CHRONIC)
MAY AFFECT THE FOLLOWING ORG ANS: RESPIRATORY TRACT, CNS, KIDNEYS,
LIVER, REPRODUCTIVE SYSTEM, CARDIAC SENSITIZATION.
Explanation of Carcinogenicity:NOT RELEVANT
Effects of Overexposure:SEE HEALTH HAZARDS.
Medical Cond Aggravated by Exposure:UNKNOWN AT THIS TIME.

First Aid:INHAL: REMOVE FROM EXPOSURE. EYE: FLUSH IMMEDIATELY WITH
LARGE AMOUNTS OF RUNNING WATER FOR AT LEAST 15 MINUTES. SKIN:
REMOVE CONTAMINATED CLOTHING AND WASH SKIN WITH SOAP AND WATER.
INGEST: DRINK WAT ER. IF NECESSARY CONSULT MD FOR ANY OF THESE
CONDITIONS.

Flash Point Method:SCC
Flash Point:22.0F,-5.6C
Lower Limits:1.20%
Extinguishing Media:USE WATER FOG, FOAM, DRY CHEMICAL OR CO2.
Fire Fighting Procedures:WEAR NIOSH/MSHA APPROVED SCBA & FULL
PROTECTIVE EQUIPMENT .
Unusual Fire/Explosion Hazard:NONE SPECIFIED BY MANUFACTURER.

Spill Release Procedures:REMOVE ALL SOURCES OF IGNITION, AVOID
BREATHING VAPS, VENTILATE AREA, AND REMOVE WITH INERT ABSORBENT &
NON- SPARKING TOOLS. BEFORE ATTEMPTING CLEANUP REFER TO INGREDIENTS
SECTION.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling and Storage Precautions:DO NOT TAKE INTERNALLY. CNTNRS SHOULD
BE GROUNDED WHEN POURING. AVOID FREE FALL OF LIQ IN EXCESS OF A FEW
INCHES.
Other Precautions:MAKE SURE THE DRUM IS COMPLETELY EMPTY BEFORE
ATTEMPTING TO WELD OR BRAZE. THE DRUM SHOULD BE INDUSTRIALLY
CLEANED PRIOR TO REUSE. DO NOT FLAME CUT, BRAZE, OR WELD WITHOUT A
NIOSH/MSHA APPROVED RESPIR ATOR OR APPROPRIATE VENTILATION.

Respiratory Protection:WHERE GENERAL DILUTION/LOCAL EXHST FAILS TO ADEQ
DILUTE TWA/PEL OF MATL, THEN RESP PROT SHOULD BE USED AS FOLLOWS:
I/A/W 29CFR 1910.134, USE NIOSH/MSHA APPRVD AIR LINE TYPE
RESP/HOODS FOR ENCLOSED & C ONFINED AREAS. NIOSH/MSHA(SEE SUPP
DATA)
Ventilation:PROVIDE GENERAL DILUTION/LOCAL EXHAUST VENT TO KEEP TWA AND
LEL BELOW ACCEPTABLE LIMITS AND TO REMOVE DECOMP PRODS.
Protective Gloves:CHEMICAL RESISTANT GLOVES.
Eye Protection:CHEMICAL WORKERS GOGGLES .
Other Protective Equipment:NONE SPECIFIED BY MANUFACTURER.
Work Hygienic Practices:NONE SPECIFIED BY MANUFACTURER.
Supplemental Safety and Health
RESP PROT: APPROVED AIR PURIFYING RESPIRATORS MAY BE USED FOR OTHER
AREAS.

HCC:F3
Boiling Pt:B.P. Text:172F,78C
Vapor Pres:SEE INGRED
Vapor Density:HVR/AIR
Spec Gravity:12.273 LBS
Appearance and Odor:NONE SPECIFIED BY MANUFACTURER.

Stability Indicator/Materials to Avoid:YES
NONE SPECIFIED BY MANUFACTURER.
Stability Condition to Avoid:NONE SPECIFIED BY MANUFACTURER.
Hazardous Decomposition Products:FUMES MAY CONTAIN CO & NOX. MAY
PRODUCE HAZARDOUS FUMES WHEN HEATED TO DECOMPOSITION AS IN WELDING.

Waste Disposal Methods:DISPOSE OF IN ACCORDANCE WITH LOCAL, STATE, AND
FEDERAL REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.